Samson S2000 Betriebsanleitung Seite 38
- Seite / 124
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
of the follower clamp (3). It must rest on
it with spring force.
Screw tight the mounting plate (21) onto
the actuator yoke using both fixing
screws.
7. Mount cover (11) on the other side.
Make sure that the vent plug points
downwards when the control valve is in
-
stalled to allow any condensed water
that collects to drain off.
4.7.2 Mounting the position
sensor with attachment
according to IEC 60534-6
For the required mounting parts and the ac
-
cessories, refer to Table 7 on page 46.
1. Place the lever (1) on the sensor in
mid-position and hold it in place.
Unthread the nut (1.1) and remove the
lever together with the disk spring (1.2)
from the sensor shaft.
2. Screw the position sensor (20) onto the
bracket (21).
The standard attached lever M with the fol
-
lower pin (2) at position 35 is designed for
120, 240 and 350 cm² actuators with
15 mm rated travel.
For other actuator sizes or travels, select the
lever and pin position from the travel table
on page 15. Lever L and XL are included in
the mounting kit.
3. Place the lever (1) and disk spring (1.2)
on the sensor shaft. Place the lever (1) in
mid-position and hold it in place. Screw
on the nut (1.1).
4. Screw both bolts (14) to the bracket
(9.1) of the stem connector (9). Attach
38 EB 8384-4 EN
Attachment to the control valve – Mounting parts and accessories
20 21
2
1.1, 1.2 14.1 3 14 99.1
Fig. 18 · Mounting according to IEC 60534-6 (NAMUR)
1 Lever
1.1 Nut
1.2 Disk spring
2 Follower pin
3 Follower plate
9 Stem connector
9.1 Bracket
14 Bolt
14.1 Screws
20 Position sensor
21 Bracket
- Mounting and 1
- Operating Instructions 1
- EB 8384-4 EN (1300-1613) 1
- EB 8384-4 EN 3 3
- EB 8384-4 EN 5 5
- Vent opening 6
- 2 Article code 7
- 3 Design and principle of 8
- 3.1 Additional equipment 9
- 3.2 Communication 10
- 3.2.1 Configuration using 10
- TROVIS-VIEW software 10
- 3.3 Technical data 11
- 12 EB 8384-4 EN 12
- 4 Attachment to the control 14
- 4.1 Direct attachment 16
- 4.1.1 Type 3277-5 Actuator 16
- 4.1.2 Type 3277 Actuator 18
- 4.2 Attachment according to 20
- IEC 60534-6 (NAMUR) 20
- 4.3 Attachment according to 22
- VDI/VDE 3847 22
- Actuator stem 24
- EB 8384-4 EN 25 25
- 4.4 Attachment to Type 3510 28
- Micro-flow Valve 28
- 4.5 Attachment to rotary 30
- 4.5.1 Heavy-duty version 32
- 4.6 Reversing amplifier for 34
- 4.6.1 Reversing amplifier 34
- (1079-1118 or 1079-1119) 34
- From the positioner 35
- Control signals to 35
- 4.7 Attaching an external 36
- 4.7.1 Mounting the position 36
- 1.1, 1.2 14.1 3 14 99.1 38
- 4.7.3 Mounting the position 39
- 2 1 1.1, 1.2 40
- 4.9 Air purging function for 41
- 4.10 Mounting parts and 42
- 44 EB 8384-4 EN 44
- Table 6 · General accessories 45
- 46 EB 8384-4 EN 46
- 5 Connections 47
- 5.1 Pneumatic connections 47
- 5.1.1 Signal pressure gauges 47
- 5.1.2 Supply pressure 47
- 5.2 Electrical connections 48
- EB 8384-4 EN 49 49
- 24 V DC BE1 BE2 50
- EB 8384-4 EN 51 51
- 52 EB 8384-4 EN 52
- Connections 52
- 6 Operator controls and 53
- 7 Start-up – Settings 56
- 7.1 Defining the valve closed 56
- 7.3 Adapting the display 57
- 7.5 Checking the operating 58
- Manual reference variable 59
- EB 8384-4 EN 59 59
- 7.6 Initialization 60
- Default No 65
- Nominal range 65
- (locked with Code 4 = No) 65
- EB 8384-4 EN 65 65
- 7.7 Zero calibration 68
- 7.8 Reset to default values 68
- 7.10 Setting the bus address 69
- 8 Operation 70
- 8.1 Enabling and selecting 70
- 8.2 Operating modes 71
- 8.2.1 Automatic and manual 71
- 8.3 Malfunction/maintenance 73
- Error caused by pin 74
- 9 Adjusting the limit switch 75
- 10 Maintenance 78
- 12 Firmware update (serial 78
- EB 8384-4 EN 79 79
- 14 Code list 80
- Code list 81
- 82 EB 8384-4 EN 82
- 84 EB 8384-4 EN 84
- 86 EB 8384-4 EN 86
- EB 8384-4 EN 87 87
- Initialization errors 88
- 88 EB 8384-4 EN 88
- Operational errors 90
- 90 EB 8384-4 EN 90
- Hardware errors 91
- Error appendix 92
- 92 EB 8384-4 EN 92
- Data errors 93
- 94 EB 8384-4 EN 94
- Diagnosis errors 95
- 15 Dimensions in mm 96
- EB 8384-4 EN 97 97
- Heavy-duty version 98
- Light version 98
- EB 8384-4 EN 100
- 102 EB 8384-4 EN 102
- EB 8384-4 EN 103 103
- 104 EB 8384-4 EN 104
- EB 8384-4 EN 105 105
- 106 EB 8384-4 EN 106
- EB 8384-4 EN 107 107
- 108 EB 8384-4 EN 108
- EB 8384-4 EN 109 109
- 110 EB 8384-4 EN 110
- EB 8384-4 EN 111 111
- 112 EB 8384-4 EN 112
- EB 8384-4 EN 113 113
- 114 EB 8384-4 EN 114
- EB 8384-4 EN 115 115
- EB 8384-4 EN 117 117
- Model 3730-43 118
- or 3730-53 118
- EB 8384-4 EN 119 119
- 122 EB 8384-4 EN 122
- EB 8384-4 EN 123 123
Verwandte Produkte und Handbücher für Audioverstärker Samson S2000
Audioverstärker Samson 1400 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Audioverstärker Samson 1200 Spezifikationen
(60 Seiten)
(60 Seiten)
Audioverstärker Samson B Series B900 Handbuch
(60 Seiten)
(60 Seiten)
Audioverstärker Samson SCOM Spezifikationen
(67 Seiten)
(67 Seiten)
(5 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.132 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern